Release Notes - Digium Analog Gateways G080

Version 2.1.3 - July 15, 2020

Bugs Fixed:

• Correct failure to properly connect to Tech Support server.

Version 2.1.2 - November 16, 2018

Bugs Fixed:

• Corrects a regression, introduced in 2.0.1 and further propagated in 2.1.0, that improperly rotated logs onto the filesystem, eventually filling it up and rendering the gateway inoperable, save for a USB filesystem recovery.
• Any customer that is running firmware 2.0.1 or 2.1.0 must upgrade to this as soon as possible.

Version 2.1.0 - September 26, 2018

Bugs Fixed:

• Updated websocket interface to address AST-2018-009

Version 2.0.1 - September 5, 2018

Bugs Fixed

• WSS Clients can now connect to gateway using SIP.
• Fixed syslog output from the gateway. Throttled back amount of nuisance data in the syslog output.
• Fixed web server caching issue when restoring configuration backups.
• DTLS certifications can now be deleted for SIP endpoints

Improvements:

• Updated critical internal software packages
• Enabled RTCP muxing on RTP streams

Version 1.3.0 - July 9, 2018

Bugs Fixed

• Correct issue where Interconnect configuration did not occur over VLAN connections
• Indicate that changes to SIP client TOS and COS settings causes calls to be dropped during their configuration.
• Remove Call Bridge logging which is not supported on the G080
• Fixed WSS port bindings and added RTCP multiplexing to SIP endpoint configuration

Version 1.2.2 - May 8, 2018

Bugs Fixed

• Correct failure to properly handle loose routing when utilizing an Outbound Proxy
• Correct failure to properly ARP on DHCP OFFER if an address had previously been assigned
• Correct failure to properly apply 802.1p bit
• Correct issue with pass-through caller ID in situations not requiring a specific From header user part

New Features:

• Allow definition of extension for locally-registered SIP Endpoint in new Survivability configuration menu.
• Allow faxes to be routed directly to FXS ports without having to use a calling rule
• Allow specification of a call rule timeout to be honored before jumping to a subsequent destination
• Prevent Gateway from Advertising itself as a Multicast service

Improvements:

• Update to Asterisk 13.18-cert3
• Update to newer OpenSSL and Apache versions
• Interconnect choices are differentiated for FXO and FXS ports.
• Provide better help for the FAX to FXS redirect feature
• Auto-convert TDM recordings from signed linear to .wav for convenience
• Prevent FXO ports from suggesting call rules with DID matching
• Provide help for the Interconnect page

Version 1.1.1 - March 14, 2018

Bugs Fixed

• Fix issues with data placed into debug logs
• Account for AST-2018-001, AST-2018-002, AST-2018-003, AST-2018-004, AST-2018-005, and AST-2018-006 issues.
• Fix issues with HTTPS certificates

Improvements:

• Add more descriptive text to bind address help.
• Added an ARPing check to DHCP address resolution on DHCP Discover requests.

Version 1.0.8 - January 18, 2018

Bugs Fixed

• Correct issue with setting time zone offset.
• Correct issue with removal of HTTPs certs on factory reset.
• Correct issue with modification and creation of ACL rules.
• Correct issue with import of custom HTTPs certs.
• Correct behavior that allowed disabling of all three Endpoint Identifier types.
• Account for AST-2017-14
• Correct issue reloading remote config on reboot.
• Correct issue with Caller Number when dialing between locally registered SIP phones.
• Correct functionality of Authentication Incoming Calls option.
• Correct issues properly setting up WSS transports.
• Correct issue preventing TLS signaling from functioning by default, without a user-supplied CA and key.
• Correct issue applying DTLS CA File to an endpoint.
• Correct issue applying changes to FXS port Caller ID Signaling types.
• Correct issues applying STUN server configuration.
• Correct issues attempting Interconnect to a Switchvox system with no configured SIP extensions.
• Correct issue with restoration of SIP Endpoints from a Backup.
• Correct issue with RTP during certain NAT scenarios.
• Correct issue with RTP during certain Endpoint-to-Endpoint scenarios.
• Correct issue generating Debugs if stopped early.
• Correct issues with TDM Debug capture.

New Features:

• Add Replace Ice Hosts option to SIP Global Networking Advanced RTP settings.
• Allow Optimistic (SRTP) Encryption for endpoints.
• Allow country tone selection for SIP endpoints.
• Add SIP Roundtrip packet Timer T1 and SIP INVITE acknowledge Timer B to SIP Global Parsing and Compatibility page.
• Allow mapping of FXS ports to remote SIP endpoint message waiting accounts (requires unsolicited MWI NOTIFY from remote server) and generation of stutter dial tone.

Improvements:

• Do not show IP for SSL Certificate option as only one Ethernet interface is available.
• Move TLS Private Key option to appear with TLS CA file option.
• Do not list “eth1” for MAC Address on System Information page as only one Ethernet interface is available.
• Refactor SDP Session Name as an endpoint, not global, option.
• Refactor SDP Owner as an advanced endpoint, not global, option.
• Disable TCP Switch has been renamed “Enable automatic switch to TCP on large requests.”
• Prevent Interconnect call rule value names from overlapping available fields.
• Allow removal of user-supplied TLS CA and key files without factory reset.
• Improve help about the use of ports in multiple Call Routing Groups.
• Add the MAC address of the unit to the Tech Support Diagnostics page.
• Remove mention of PRI channels from Call Routing Groups page.
• Maximum Endpoint Expiry has bee renamed to Registration Expiration.
• Remote Secret has been renamed to Remote Authentication Password.
• Restrict the SIP Realm field to scenarios using outbound or no registration only.
• Default TLS port to 5061.
• Enable UDP Checksums has been renamed Enable RTP Checksums.
• Strict RTP has been renamed Drop RTP Packets not from stream source.
• RTP Source Probation has been renamed Packets required to change source.
• From User has been renamed Overwrite User in From Header.
• From Domain has been renamed Overwrite Domain in From Header.
• Remote Secret has ben renamed Remote Password.
• 802.1P Priority has been renamed 802.1p CoS Bit
• TOS has been renamed DSCP TOS byte
• Remove global Default User as its functionality is instead handled at the endpoint level.